Battle-of-the-bands.info/blog

It isn’t the tools that are used in a job that make it good or bad, it’s the person using those tools that makes the difference. In car polishing a good technician can make that finish look better than when you bought the car, and you wouldn’t think twice about how they could do that. In this short article, I will go over some points that technicians know, or should know.

The main problems when it comes to auto finishing are things like paint runs, sags, dirt nibs and just plain old polishing in general. To start with, make sure that the finish is dry in accordance with the information from the product sheet as failure to do this could damage the finish, making the whole job very costly.

The proper way to polish when using a polish, make sure it is specifically or can be used for urethane finishes and not lacquer finishes. When sanding, make sure that you use the finer 1000grit paper, as course grit sandpaper can ruin a finish.

The polisher speed should be set at 1200 ? 1700 rpm?s to ensure the best result. It is also very important to make sure that you are using the right type of pad before you start. To know what the best pad types, always check the product data sheets and they?ll steer you in the right direction, remember, if in doubt, check the sheet.

On the blend edges when you are, polishing be sure to work away from the edge and never directly into it. The most recommended method for a blend edge is to hand glaze rather than machine polish. When you have to hand glaze, always a cloth that is not rough and make sure it is clean forboth the application and when taking the glaze off.

Getting Rid Of Imperfections As with polishing, always check with the right manufacturers product data sheet before sanding, or polishing, this will give you the recommended dry times before polishing. Always make sure that before you begin any work on the surface that you take off debris and material. If this isn?t done, the results will be costly and catastrophic.

It is so important that the proper prep work be done so that the surface is: Free of imperfections like dirt nibs. You can use 1500 or better grit for wet sanding to get rid of these. To make sure there are no more imperfections on the surface, sand the surface with a block sander, not necessarily the entire surface, spot sanding will do.

The Last Step Use the polisher lightly to eliminate sand scratches using the right liquid polish. When using the polisher, set it to 1200 ? 1700 rpm and use a wool pad first. Next, you will need to use a foam pad. Finally, you need a non- abrasive glaze. Always remember that if you are in doubt about what to use or how to do it, consult the manufacturer?s list of instruction and information data sheet .Don?t be in a hurry, if you take your time you won?t make the mistakes that you will only regret.

Tags: Arts & Entertainment by Mario Goldstein
No Comments »

Respraying your car implies you’re prepared to devote some time and money to complete this project. Theres zero reason why you can’t do this yourself, but you are going to need some guide lines. Unless of course you are already a professional car painter.

Firstly make up your mind to accept that youre not going to get the same professional looking job by utilising spray paints from a can. That is not to say you cant use them and get correct results. Just do not raise your expectations to high. Respraying your car would take some getting used to.

1st Step: Do all of your sanding of the rough spots, and filling of the holes. Theres no point in doing this after you have cleaned the car you’ll just be defeating the purpose of washing the car in the first place.

2nd step: You must begin with a clean car. If you dont then your final paint finish will be a mess. Every last bit of debris that you left on the car would be obvious after the respraying.

Hint: If your car is wet and you shine a light on it you will clearly see whatsoever imperfections that you didnt catch in the first or second step

Third Step Now youve to mask off all of the regions where you don’t want paint. If you arent genuinely diligent in this step you could end up being genuinely sorry that you didn’t. It would be a pity to have a pretty paint finish, but half the paint is on the windows or chrome.

4th Step Practise a bit with your spray. There’s a bit of a technique to it. Keep in mind we said that re-spraying your car does take quite a long time. Practice on a piece of cardboard. That way you’re not as likely to get squirts or blobs of paint. Keep the spray moving continuously, and in really light coats. A couple of light coats of paint are far superior to two thick ones, that’ll look very uneven.

5th Step Allow the coats of paint to dry at least 1 hour in between. Then apply the finishing coat. Once more this should be applied simply like the paint. A flowing motion with merely a really light coating.

By taking your time to do the job right and following these respraying instructions you should end up with a very great completed project. If you try and take short-cuts then this is where your troubles will start.

Be certain you utilize good quality equipment and products. Slowly take your time, because when you begin to rush a stage then that’s where mistakes take place. Keep in mind to use the right safety measures such as the correct protective gear.

Ideally it helps to be able to re-spray your car on a warm sunny day, as it helps to set or bake the paint on, giving it a better finish.

So remember before you start out, do your search on the how tos and have each your tools and supplies at hand, and youre ready to go for it.

Tags: Arts & Entertainment by Elen Hallman
No Comments »

You could be really successful at painting your car, provided youve a good plan, the right budget and the time. And also you’ll most surely need the right tools and equipment. Oh yeah, and you would need a nice and spacious work area.

Frequently inexperienced individuals feel that all they need to paint their motor vehicles, is a few cans of car paint, and thats it. It does not function that way, and if it did then there would be a great deal of car painters out of business.

Tools and equipment to paint your car are not a large expense, but you do need them.

Item one To start with you’ll need a good car-wash detergent and a degreaser. The car must be perfectly clean before you set out.

Item #2 A variety of grits of sand-paper. Probably there are going to be a few uneven spots that you would need to smooth out.

Item three Putty and a putty knife. Almost every vehicle suffers from those nasty pits that flying stones cause. This is often one of the reasons to prompt you to paint the motor vehicle in the first place.

Item four Masking tape and paper to cover the regions that you don’t want to get paint on. Don’t make the error of thinking that you are good enough with a spray can so you can pass this step. One small gust of wind is all it needs to spot the chrome with over flow paint.

Item five Now you are getting closer to genuinely getting down to starting. You would require the primer. How much you need reckons on the amount of sanding and filling you had to do.

Item #6 The paint is of your choice. What colors and brands youre going to utilise is the decision you need to make here.

Item seven One of the most fundamental items is the top coat. You actually need to protect that beautiful paint job once you’re complete.

These’re numerous of the tools and equipment plus product you’ll need to do your job effectively. There are various items that we need to speak about abit more in depth. For instance, how’re you going to apply your paint? You will have chose to go with the aerosol spray paints. In this case you will not require much more to apply the paint. In the case that you have decided to purchase paints that require a spray gun, then you must include this in your tools and equipment list.

Some other item under tools and equipment although nonobligatory is an electric sander. If you have lots of sanding to do then genuinely consider either renting or borrowing one of these if you do not own them. It could save you a great deal of time and comfort too.

Bear in mind it is important that you clean every of your tools and equipment correctly once you have finished the job. A couple of the items are not all that low-cost and you will never know when your next paint job will come up.

Tags: Arts & Entertainment by Will Yonder
No Comments »

There are disadvantages and advantages with painting your car yourself and going to the workshop to paint.

Reasons to Paint Your Own Car.

1.It’s a money saver or at least could be if you do it right of course. If you don’t take the time to study to do it the right way then it could still be a costly endeavor.

2. it’s a great achievement to complete this task then be able to stand back and look at the great job you’ve done.

Three. If you’re into car restoration, its one way you could cut down your expenses.

Four. Often there’s preliminary work that you would have to do yourself before you get to the point of car painting itself.

Reasons To Paint Your Shop In A Car

1. It is most likely a time saver. Unless you have the excess time to spend car painting, then this would be the route you want to go. Do not forget there’s more to it than just putting the paint on.

Two. The shop more than likely has much better car painting tools then you would have. This means they could get a pretty finish.

3. The quality of the paint they use perhaps is better than what youre able to purchase.

4. They know how to complete the needed body work first as they’ve professionals on staff specifically for that task.

5. Reputable enterprises would stand behind their work. Put differently they’ll give you various type of guarantee.

Six. They’ve the commercial products to clean the car prior to car painting, which’s exceedingly significant.

Seven. They have the correct facilities, where as if you do it yourself you would not be able to protect the car against the factors in case you can’t get it finished.

So as you could see there are advantages and disadvantages for both arguments. If you could improvise and create the identical circumstances as for the favourable points of utilising a shop then you will want to consider it. Car painting is a serious undertaking. Another thing you may want to consider as well is the value of the car. If it is a second motor vehicle or a somewhat old one then maybe you do not want to pay the fees of having it professionally painted. In this case you would probably be further ahead to do the car painting yourself. In these circumstances small flaws in the overall work isnt gonig to make a difference.

The other point is if youve various experience with car painting or even some other types of spray painting then you may be able to do a good job with out putting it into a shop. These’re all things you will need to consider. If you decide that you’re going to do it yourself though it will be a good idea to read up some how to books or watch a video on the subject.

Tags: Arts & Entertainment by Elen Hallman
No Comments »

When a professional collision repairer wants to bring a vehicle to its pre loss condition the best takes its cues from the aviation industry because the fasteners are very important to the life and safety of the vehicle they are working on. They have predestinated specifications for airplanes fasteners and many times these are scrutinized to make sure they are tightened correctly and if an accident ever occurs this is one main component that is looked at with great length to find out if it was a bolt or screw that loosened that could be a contributing factor!

With that being said although, vehicles may not go through the rigorous stresses an airplane may suffer it is still essential to make sure the right bolt or screw is fastened correctly. If not you, may experience squeaks, rattles, and it may ultimately impair the safety and resale value of the vehicle and cause premature failure. Many buyers are now informed on what to look for including missing bolts or different sizes not meeting specs.

When automotive engineers choose fasteners they do it for a reason and those who repair vehicles have to follow the specific requirements. This is essential, because of the different torque qualities these fasteners must be installed 100% correct. Not only can the look of your car can be affected, but the performance as well. Reports have been done that show certain fasteners on your bumpers and quarter panels if reinstalled incorrectly can cause certain expansion and allow movement, which can ultimately lead to serious damage to your vehicle after time.

When Clamping Down Fasteners Fasteners all include certain characteristics. They have a grade and tensile strength, which determines how much they can stretch before breakage. The diameter and type of material determine the resistance of this. The English system defines the strength of a bolt by radial lines with property numbers such as 4.6, 4.8, 5.8, 8.8 9.8 and 10.9 and the nuts must be appropriately classed to each fastener to ensure the same grade and work equally to the fastener that is installed. Nuts attached to the fastener have their own grading system with some using dots to determine their tensile strength and some using actual numbers. Always be fastidious to match the correct pair and that will ensure optimal matching connection. If you deviate from this, you can lose the connection state.

Some Important Variables You need to ensure the parts are secured correctly .This just means that enough force is needed to bind the components within the specifications so that parts cannot shift under regular movement.

Many times a factor of a connection can be achieved by using a pitch gauge, which can determine if a bolt or screw is tightened to its specifications. A thread pitch can sometimes be a factor and by reading the manufacturers design codes you can decrease the problems of making a bad connection which can lead to problems down the road.

Tags: Arts & Entertainment by Mario Goldstein
No Comments »

So you only finished putting that first coat of paint on that car that you have been mending and it looks great. You didnt realise that you had to the talent to spray paint a car. The only one problem is you’ve run out of time and cannot get the second coat on. Well that is really not going to be a problem, the cars in a well-kept area so you could get back at it next week. You just stick the caps on the spray cans and stick them on the shelf for the time you are gone.

A week goes by and you are ready to go ahead and spray paint the car, or at least get the second coat on. Youre all set up you’ve pulled the cans of spray paint off the shelf, and popped the lid on one of them. Then it doesnt seem to matter how hard you press the nozzle of the spray can nothing comes out. You remember that you didnt use it and it is almost full. Then you realise it must be clogged. No problem you merely get a thin piece of wire and try to clean it out.

After a couple of tries you realise it just isnt going to clear, so you end up throwing an almost full can of rather expensive spray paint away. Then you remember what a buddy told you about spray paints. When you are finished using them you must turn the can upside down and spray the paint for few seconds. This can be done on a piece of cardboard. It’ll clear all the unnecessary spray out of the nozzle so in future you go to use it, it wont be blocked. A good lesson learned.

You did not realise the troubles that can occur when you went to spray paint a car, but gratefully youve a few cans of paint left so you could get on with it. You give the cans a couple of shakes and ultimately out comes the paint. There’s one big problem though, the color does not look quite the same. The label says it’s the similar color but what in the world is the problem here? Actually you most likely didnt shake well so the colour was not correctly mixed. You must shake the can quickly you would hear the mixer ball inside the can rattle. Continue to shake for at least 3 to 4 minutes. Also at regular intervals while you’re spraying give the can a hard shake also. This will ensure that your paint stays well-mixed and would evenly distribute the colour when you apply it. Keep in mind you must be as methodical when you go to spray paint a car, as you would a fine piece of furniture.

Some other very significant point to remember is that to spray paint a car is a large job, and most likely you would be a little tired afterwards. Clean up is really fundamental and that means making sure that you cleaned the nozzle of the spray as we discussed. Some other very essential thing to keep in mind is to keep your paints safely. Do not leave them in places where they could dry or freeze.

Tags: Arts & Entertainment by Will Yonder
No Comments »

When buying a car one of the biggest choices you have is the color! Though there are many choices to make it?s the main factor that you can decide on which suits you best and appeals to your sense of style. Black is a big seller yet silver can sometimes have more style. Red is hot and white can be conservative, it?s all up to you.

The elements though can play havoc on keeping that original shine and luster to this important investment. Once a car loses its color, the value is reduced and it never looks the same. These are some tips and tricks on how to maintain that color and keep the environment from doing damage to your paint job as well as restoring any damage already done!

HOW TO RESIST ENVIROMENTAL DAMAGES There are many different types of finishes on vehicles like enamel, matt coating, acrylic etc?unfortunately, no matter what the finish is, your car?s paint is still susceptible to the environment. To help protect it always use a preventive maintenance program. The sun puts out ultra violet rays that can damage the gloss of the finish and because metal holds heat it can cause permanent stains. The only way to deal with this is by using protective sealants and coatings.

Air pollutants are your next problem because they transform into nitric and sulfuric acids that eventually deposit onto your vehicle and eat up the paint. To combat this, keep your vehicle clean by washing it on a regular basis. This is very important because even in the winter with salt and dirt, pitting and rusting can occur. The undercarriage should be treated with a protective coating to help eliminate this problem.

When your car is clean moisture can’t build up in the dirty areas and cause corrosion. I advise a car wash at least once to twice a month and sometimes have a gentle power wash to dislodge dirt that is embedded in hard to reach places like under the bumpers, the wheel wells and behind the moldings to name a few.

By pressure washing after or during winter you can dislodge the excess salt and dirt from the body of your vehicle and at the same time give it a shiny and clean appearance and reduce the chances of rust problems.

Another big tip is to keep you car or truck waxed on a regular basis. This will aid in a big way to keep the color from fading and minimize the harm that chemicals can do to your paint job and also give a great shine to your vehicle. Its should only take about 30 minutes to wax even a large vehicle and should last for 3-4 months.

ALWAYS REPAIR THE CHIPS AND SCRATCHES Most times you can order matching spray paint from the manufacturer and buy using a toothpick as an aid you can fix most prominent scratches and chips. For some of the smaller ones a polishing compound will work.

By investing, the time and utilizing these tips your vehicles paint job has a much better chance of remaining in new like condition!

Tags: Arts & Entertainment by Mario Goldstein
No Comments »

With money being tight at present, perhaps the answer to giving your car a fresh look would be to indulge in some car spray painting. If the mechanics of it are in good shape, but the body is not so hot, then painting it may be the ideal solution.

It is a remarkable money-saver, but even more so if you do it yourself as opposed to getting it professionally done. You can do it if you read the basics and follow the instructions for car spray painting. Its important though if you decide you are going to take on this project that youre ready to see it through till the end.

Firstly, you need numerous supplies. These consist of:

-coverings to protect the unpainted areas and masking tape to hold these in place -a good car wash detergent and brush and also a wax/grease remover. -various grits of sandpaper -primers and paint thats urethane base for the car spray painting -paint sprayer -safety equipment like masks, goggles and protective clothing -knife and putty for fill ins.

One : You must make sure that you wash the car thoroughly to remove all grime and debris. If you don’t then these things would be set in with your paint, giving a very daunting look to the completed job. Follow up with a wax/grease remover so the paint you utilize for the car spray painting would adhere the right way.

Two : Get rid of any rough spots by sanding. Once this has been done be certain to rinse off whatever of the loose sandings. This’s where you will want to utilise the putty to fill in whatever small pit marks, that’re have been caused from stones for example.

Three : Dont get in too much of a rush to begin your car spray painting. The car must be totally dry so its best to leave it to do so for few hours. You could go ahead and cover whatsoever of the areas that your dont want to get paint on.

Four : At present you are ready to set out with the primer. Don’t skip this step, as it will give a much better look to the finished project. It helps the paint to adhere properly and provides for a more even finish. Next, once the primer is dry you’ll need to gently sand it down.

Five : You are finally at the step youve been waiting for. It’s time to apply the color for your car spray painting. Whether youve opted to use aerosol paints or a spray gun, the premise stays the same. Simply apply thin coats. Several will likely be required. Many light coats are much better than one thick coat. You’ll be able to tell simply by looking at the car how many more coats of paint it’ll require. Various might just need 2 whereas a few others may require three or four.

Six : In conclusion, down to the last step and thats applying the clear coat. This is done exactly the same as the colored coats.

Now you could clean up, take a step back and look up to the masterpiece you’ve created.

Tags: Arts & Entertainment by Bojan Palen
No Comments »

The Wii console is everywhere now, many people have purchased the Nintendo Wii for their families or to play with their friends. The Wii Fit helped bring the console to many more users than if it were only a gaming console. So what’s next for the Nintendo Wii game system?

Nintendo has released or will be releasing plenty of new stuff. One big release was in May 2009 of the new Wii MotionPlus accessory. This accessory adds better control to the Wii’s motion-sensitive controller, so playing games is more accurate. Players can improve their play in things like golf and tennis, as well as battle games. To take advantage of the MotionPlus, a new version of Wii Sports is out, caled Wii Sports Resort.

There is also a new Wii console bundle coming too, with the new Sports Resort game and also the MotionPlus. Wii bundles come with a console, and some have new games also, for new users who haven’t purchased a console yet, but want to get one now with the new games coming out.

Nintendo is also developing a new “vitality sensor”, which is a clip onto your fingertip with a sensor using a light sensor to read your biorhythms. The idea is that this would then measure your brain waves, giving users access to biofeedback readings. The possibile uses are to learn meditation, reduce blood pressure, learn tof ocus and concentrate – if it works as proposed! This accessory is targeted for release in 2010, but is not yet confirmed by Nintendo.

Nintendo keeps attracting plenty of non-gamers to its console, with new games and fun for anyone, not just gamers. The perfect example is the Wii Fit which was huge for Nintendo, and helps anyone of any age start and maintain a fitness program using the balance board to work out, track progress, and build workout routines.

Nintendo and its game partners are releasing more sports games too, which means Wii Sports bundles will have great options for games and accessories. Two new ones are Virtua Tennis from Sega and Grand Slam Tennis from EA Sports. Grand Slam Tennis takes advantage of the new MotionPlus.

Another kick-butt release, EA Sports Active, adds a sensor pad for users to strap onto their leg, helping track body movements while running, jumping, and kicking. This kind of innovation will keep the Wii console at the top of the hot list for some time.

Tags: Games by Sue Calhoun
No Comments »

The Nintendo Wii is unlike any other video game system which has come before; it has generated an unprecedented level of popularity. It should come as no surprise to anyone that there are a lot of people who want to copy their Wii games as a backup in case of damage, loss or theft.

While these games come on a disc that looks a lot like your burnable CDs, they can’t just be copied the same way you’d rip a music CD. It’s a little more complicated than that. Here’s a guide to tell you the basics of copying Wii games, as well as the circumstances when you should and shouldn’t do it.

Your standard CD burning software can’t copy Wii games. Nero, Roxio and other common CD burning software doesn’t have the capabilities of breaking the copy protection which is encoded in to Wii games and other game discs. Your computer cannot make sense of the data on the disc because of this encryption.

However, no sooner is a new encryption method invented than someone finds a way around it ? the copy protection on Wii games is no exception. There is a lot of software out there which can break the encryption on WIi game discs.

This copy protection breaking software makes copying Wii games as simple as a few mouse clicks. With the software installed, your computer will be able to make sense of the datat on the game disc. Better yet, it’s not just Wii discs which can be read using this software; PS3 and Xbox games can also be read.

Many games made for PCs also use encryption which can be cracked with this software. If you have multiple gaming systems, you can use this software to make backups of these games as well as your Wii games.

With this encryption breaking software, you can make a disc image of the Wii game and copy it on to your hard drive. You can use your regular CD burning software to make a copy of this disc just as you would when copying any other CD or DVD.

These programs often feature burning and copying capabilities along with their decryption abilities. Using these built in tools, you’ll have a smaller chance of burning errors when copying Wii games.

Thanks to these new software tools, copying Wii games is not quick and easy. It’s always a good idea to have backups of your favorite games in case of accidents, theft or loss. Happy gaming!

Tags: Games by Cam Halladay
No Comments »